[PATCH net-next v5 0/7] net: stmmac: Add support for RZN1 GMAC devices

[PATCH net-next v5 0/7] net: stmmac: Add support for RZN1 GMAC devices

[Romain Gantois]

Hello everyone,

This is version five of my series that adds support for a Gigabit Ethernet
controller featured in the Renesas r9a06g032 SoC, of the RZ/N1 family. This
GMAC device is based on a Synopsys IP and is compatible with the stmmac driver.

My former colleague Clément Léger originally sent a series for this driver,
but an issue in bringing up the PCS clock had blocked the upstreaming
process. This issue has since been resolved by the following series:

https://lore.kernel.org/all/20240326-rxc_bugfix-v6-0-24a74e5c761f@bootlin.com/

This series consists of a devicetree binding describing the RZN1 GMAC
controller IP, a node for the GMAC1 device in the r9a06g032 SoC device
tree, and the GMAC driver itself which is a glue layer in stmmac.

There are also two patches by Russell that improve pcs initialization handling
in stmmac.

Best Regards,

Romain Gantois

---
Changes in v5:
- Refactored the stmmac_xpcs_setup() function to group together XPCS and PCS
  setup logic.
- Added a stmmac_pcs_clean() function as a counterpart to stmmac_pcs_setup()
- Link to v4: https://lore.kernel.org/r/20240424-rzn1-gmac1-v4-0-852a5f2ce0c0@bootlin.com

Changes in v4:
- Removed the second parameters of the new pcs_init/exit() callbacks
- Removed unnecessary interrupt-parent reference in gmac1 device node
- Link to v3: https://lore.kernel.org/r/20240415-rzn1-gmac1-v3-0-ab12f2c4401d@bootlin.com

Changes in v3:
- Fixed a typo in the socfpga patch
- Link to v2: https://lore.kernel.org/r/20240409-rzn1-gmac1-v2-0-79ca45f2fc79@bootlin.com

Changes in v2:
- Add pcs_init/exit callbacks in stmmac to solve race condition
- Use pcs_init/exit callbacks in dwmac_socfpga glue layer
- Miscellaneous device tree binding corrections
- Link to v1: https://lore.kernel.org/r/20240402-rzn1-gmac1-v1-0-5be2b2894d8c@bootlin.com

---
Clément Léger (3):
      dt-bindings: net: renesas,rzn1-gmac: Document RZ/N1 GMAC support
      net: stmmac: add support for RZ/N1 GMAC
      ARM: dts: r9a06g032: describe GMAC1

Russell King (Oracle) (2):
      net: stmmac: introduce pcs_init/pcs_exit stmmac operations
      net: stmmac: dwmac-socfpga: use pcs_init/pcs_exit

Serge Semin (2):
      net: stmmac: Add dedicated XPCS cleanup method
      net: stmmac: Make stmmac_xpcs_setup() generic to all PCS devices

 .../devicetree/bindings/net/renesas,rzn1-gmac.yaml |  66 +++++++++++++
 MAINTAINERS                                        |   6 ++
 arch/arm/boot/dts/renesas/r9a06g032.dtsi           |  18 ++++
 drivers/net/ethernet/stmicro/stmmac/Kconfig        |  12 +++
 drivers/net/ethernet/stmicro/stmmac/Makefile       |   1 +
 drivers/net/ethernet/stmicro/stmmac/dwmac-rzn1.c   |  86 +++++++++++++++++
 .../net/ethernet/stmicro/stmmac/dwmac-socfpga.c    | 107 ++++++++++-----------
 drivers/net/ethernet/stmicro/stmmac/stmmac.h       |   3 +-
 drivers/net/ethernet/stmicro/stmmac/stmmac_main.c  |  14 +--
 drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c  |  48 ++++++---
 include/linux/stmmac.h                             |   2 +
 11 files changed, 287 insertions(+), 76 deletions(-)
---
base-commit: dd1941f801bc958d2ee13f5be8b38db6b034b806
change-id: 20240402-rzn1-gmac1-685cf8793d0e

Best regards,
-- 
Romain Gantois <romain.gantois@bootlin.com>

[PATCH net-next v5 0/7] net: stmmac: Add support for RZN1 GMAC devices

[Romain Gantois]

Hello everyone,

This is version five of my series that adds support for a Gigabit Ethernet
controller featured in the Renesas r9a06g032 SoC, of the RZ/N1 family. This
GMAC device is based on a Synopsys IP and is compatible with the stmmac driver.

My former colleague Clément Léger originally sent a series for this driver,
but an issue in bringing up the PCS clock had blocked the upstreaming
process. This issue has since been resolved by the following series:

https://lore.kernel.org/all/20240326-rxc_bugfix-v6-0-24a74e5c761f@bootlin.com/

This series consists of a devicetree binding describing the RZN1 GMAC
controller IP, a node for the GMAC1 device in the r9a06g032 SoC device
tree, and the GMAC driver itself which is a glue layer in stmmac.

There are also two patches by Russell that improve pcs initialization handling
in stmmac.

Best Regards,

Romain Gantois

---
Changes in v5:
- Refactored the stmmac_xpcs_setup() function to group together XPCS and PCS
  setup logic.
- Added a stmmac_pcs_clean() function as a counterpart to stmmac_pcs_setup()
- Link to v4: https://lore.kernel.org/r/20240424-rzn1-gmac1-v4-0-852a5f2ce0c0@bootlin.com

Changes in v4:
- Removed the second parameters of the new pcs_init/exit() callbacks
- Removed unnecessary interrupt-parent reference in gmac1 device node
- Link to v3: https://lore.kernel.org/r/20240415-rzn1-gmac1-v3-0-ab12f2c4401d@bootlin.com

Changes in v3:
- Fixed a typo in the socfpga patch
- Link to v2: https://lore.kernel.org/r/20240409-rzn1-gmac1-v2-0-79ca45f2fc79@bootlin.com

Changes in v2:
- Add pcs_init/exit callbacks in stmmac to solve race condition
- Use pcs_init/exit callbacks in dwmac_socfpga glue layer
- Miscellaneous device tree binding corrections
- Link to v1: https://lore.kernel.org/r/20240402-rzn1-gmac1-v1-0-5be2b2894d8c@bootlin.com

---
Clément Léger (3):
      dt-bindings: net: renesas,rzn1-gmac: Document RZ/N1 GMAC support
      net: stmmac: add support for RZ/N1 GMAC
      ARM: dts: r9a06g032: describe GMAC1

Russell King (Oracle) (2):
      net: stmmac: introduce pcs_init/pcs_exit stmmac operations
      net: stmmac: dwmac-socfpga: use pcs_init/pcs_exit

Serge Semin (2):
      net: stmmac: Add dedicated XPCS cleanup method
      net: stmmac: Make stmmac_xpcs_setup() generic to all PCS devices

 .../devicetree/bindings/net/renesas,rzn1-gmac.yaml |  66 +++++++++++++
 MAINTAINERS                                        |   6 ++
 arch/arm/boot/dts/renesas/r9a06g032.dtsi           |  18 ++++
 drivers/net/ethernet/stmicro/stmmac/Kconfig        |  12 +++
 drivers/net/ethernet/stmicro/stmmac/Makefile       |   1 +
 drivers/net/ethernet/stmicro/stmmac/dwmac-rzn1.c   |  86 +++++++++++++++++
 .../net/ethernet/stmicro/stmmac/dwmac-socfpga.c    | 107 ++++++++++-----------
 drivers/net/ethernet/stmicro/stmmac/stmmac.h       |   3 +-
 drivers/net/ethernet/stmicro/stmmac/stmmac_main.c  |  14 +--
 drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c  |  48 ++++++---
 include/linux/stmmac.h                             |   2 +
 11 files changed, 287 insertions(+), 76 deletions(-)
---
base-commit: dd1941f801bc958d2ee13f5be8b38db6b034b806
change-id: 20240402-rzn1-gmac1-685cf8793d0e

Best regards,
-- 
Romain Gantois <romain.gantois@bootlin.com>


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH net-next v5 1/7] dt-bindings: net: renesas,rzn1-gmac: Document RZ/N1 GMAC support

[Romain Gantois]

From: Clément Léger <clement.leger@bootlin.com>

The RZ/N1 series of MPUs feature up to two Gigabit Ethernet controllers.
These controllers are based on Synopsys IPs. They can be connected to
RZ/N1 RGMII/RMII converters.

Add a binding that describes these GMAC devices.

Signed-off-by: Clément Léger <clement.leger@bootlin.com>
[rgantois: commit log]
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
---
 .../devicetree/bindings/net/renesas,rzn1-gmac.yaml | 66 ++++++++++++++++++++++
 1 file changed, 66 insertions(+)

diff --git a/Documentation/devicetree/bindings/net/renesas,rzn1-gmac.yaml b/Documentation/devicetree/bindings/net/renesas,rzn1-gmac.yaml
new file mode 100644
index 0000000000000..d9a8d586e260c
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/renesas,rzn1-gmac.yaml
@@ -0,0 +1,66 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/renesas,rzn1-gmac.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas GMAC
+
+maintainers:
+  - Romain Gantois <romain.gantois@bootlin.com>
+
+select:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - renesas,r9a06g032-gmac
+          - renesas,rzn1-gmac
+  required:
+    - compatible
+
+allOf:
+  - $ref: snps,dwmac.yaml#
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - renesas,r9a06g032-gmac
+      - const: renesas,rzn1-gmac
+      - const: snps,dwmac
+
+  pcs-handle:
+    description:
+      phandle pointing to a PCS sub-node compatible with
+      renesas,rzn1-miic.yaml#
+
+required:
+  - compatible
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/r9a06g032-sysctrl.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    ethernet@44000000 {
+      compatible = "renesas,r9a06g032-gmac", "renesas,rzn1-gmac", "snps,dwmac";
+      reg = <0x44000000 0x2000>;
+      interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
+                   <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>,
+                   <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+      interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+      clock-names = "stmmaceth";
+      clocks = <&sysctrl R9A06G032_HCLK_GMAC0>;
+      power-domains = <&sysctrl>;
+      snps,multicast-filter-bins = <256>;
+      snps,perfect-filter-entries = <128>;
+      tx-fifo-depth = <2048>;
+      rx-fifo-depth = <4096>;
+      pcs-handle = <&mii_conv1>;
+      phy-mode = "mii";
+    };
+
+...

-- 
2.44.0

[PATCH net-next v5 1/7] dt-bindings: net: renesas,rzn1-gmac: Document RZ/N1 GMAC support

[Romain Gantois]

From: Clément Léger <clement.leger@bootlin.com>

The RZ/N1 series of MPUs feature up to two Gigabit Ethernet controllers.
These controllers are based on Synopsys IPs. They can be connected to
RZ/N1 RGMII/RMII converters.

Add a binding that describes these GMAC devices.

Signed-off-by: Clément Léger <clement.leger@bootlin.com>
[rgantois: commit log]
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
---
 .../devicetree/bindings/net/renesas,rzn1-gmac.yaml | 66 ++++++++++++++++++++++
 1 file changed, 66 insertions(+)

diff --git a/Documentation/devicetree/bindings/net/renesas,rzn1-gmac.yaml b/Documentation/devicetree/bindings/net/renesas,rzn1-gmac.yaml
new file mode 100644
index 0000000000000..d9a8d586e260c
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/renesas,rzn1-gmac.yaml
@@ -0,0 +1,66 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/renesas,rzn1-gmac.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas GMAC
+
+maintainers:
+  - Romain Gantois <romain.gantois@bootlin.com>
+
+select:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - renesas,r9a06g032-gmac
+          - renesas,rzn1-gmac
+  required:
+    - compatible
+
+allOf:
+  - $ref: snps,dwmac.yaml#
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - renesas,r9a06g032-gmac
+      - const: renesas,rzn1-gmac
+      - const: snps,dwmac
+
+  pcs-handle:
+    description:
+      phandle pointing to a PCS sub-node compatible with
+      renesas,rzn1-miic.yaml#
+
+required:
+  - compatible
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/r9a06g032-sysctrl.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    ethernet@44000000 {
+      compatible = "renesas,r9a06g032-gmac", "renesas,rzn1-gmac", "snps,dwmac";
+      reg = <0x44000000 0x2000>;
+      interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
+                   <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>,
+                   <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+      interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+      clock-names = "stmmaceth";
+      clocks = <&sysctrl R9A06G032_HCLK_GMAC0>;
+      power-domains = <&sysctrl>;
+      snps,multicast-filter-bins = <256>;
+      snps,perfect-filter-entries = <128>;
+      tx-fifo-depth = <2048>;
+      rx-fifo-depth = <4096>;
+      pcs-handle = <&mii_conv1>;
+      phy-mode = "mii";
+    };
+
+...

-- 
2.44.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH net-next v5 2/7] net: stmmac: Add dedicated XPCS cleanup method

[Romain Gantois]

From: Serge Semin <fancer.lancer@gmail.com>

Currently the XPCS handler destruction is performed in the
stmmac_mdio_unregister() method. It doesn't look good because the handler
isn't originally created in the corresponding protagonist
stmmac_mdio_unregister(), but in the stmmac_xpcs_setup() function. In
order to have more coherent MDIO and XPCS setup/cleanup procedures,
let's move the DW XPCS destruction to the dedicated stmmac_pcs_clean()
method.

This method will also be used to cleanup PCS hardware using the
pcs_exit() callback that will be introduced to stmmac in a subsequent
patch.

Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Co-developed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
---
 drivers/net/ethernet/stmicro/stmmac/stmmac.h      |  1 +
 drivers/net/ethernet/stmicro/stmmac/stmmac_main.c |  6 +++++-
 drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c | 12 +++++++++---
 3 files changed, 15 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
index dddcaa9220cc3..7e0d727ed795b 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
@@ -361,6 +361,7 @@ int stmmac_mdio_unregister(struct net_device *ndev);
 int stmmac_mdio_register(struct net_device *ndev);
 int stmmac_mdio_reset(struct mii_bus *mii);
 int stmmac_xpcs_setup(struct mii_bus *mii);
+void stmmac_pcs_clean(struct stmmac_priv *priv);
 void stmmac_set_ethtool_ops(struct net_device *netdev);
 
 int stmmac_init_tstamp_counter(struct stmmac_priv *priv, u32 systime_flags);
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 59bf83904b62d..2a55c5d07f6b8 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -7789,8 +7789,9 @@ int stmmac_dvr_probe(struct device *device,
 
 error_netdev_register:
 	phylink_destroy(priv->phylink);
-error_xpcs_setup:
 error_phy_setup:
+	stmmac_pcs_clean(priv);
+error_xpcs_setup:
 	if (priv->hw->pcs != STMMAC_PCS_TBI &&
 	    priv->hw->pcs != STMMAC_PCS_RTBI)
 		stmmac_mdio_unregister(ndev);
@@ -7832,6 +7833,9 @@ void stmmac_dvr_remove(struct device *dev)
 	if (priv->plat->stmmac_rst)
 		reset_control_assert(priv->plat->stmmac_rst);
 	reset_control_assert(priv->plat->stmmac_ahb_rst);
+
+	stmmac_pcs_clean(priv);
+
 	if (priv->hw->pcs != STMMAC_PCS_TBI &&
 	    priv->hw->pcs != STMMAC_PCS_RTBI)
 		stmmac_mdio_unregister(ndev);
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
index 0542cfd1817e6..508bd39cbe2b3 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
@@ -523,6 +523,15 @@ int stmmac_xpcs_setup(struct mii_bus *bus)
 	return 0;
 }
 
+void stmmac_pcs_clean(struct stmmac_priv *priv)
+{
+	if (!priv->hw->xpcs)
+		return;
+
+	xpcs_destroy(priv->hw->xpcs);
+	priv->hw->xpcs = NULL;
+}
+
 /**
  * stmmac_mdio_register
  * @ndev: net device structure
@@ -679,9 +688,6 @@ int stmmac_mdio_unregister(struct net_device *ndev)
 	if (!priv->mii)
 		return 0;
 
-	if (priv->hw->xpcs)
-		xpcs_destroy(priv->hw->xpcs);
-
 	mdiobus_unregister(priv->mii);
 	priv->mii->priv = NULL;
 	mdiobus_free(priv->mii);

-- 
2.44.0

[PATCH net-next v5 2/7] net: stmmac: Add dedicated XPCS cleanup method

[Romain Gantois]

From: Serge Semin <fancer.lancer@gmail.com>

Currently the XPCS handler destruction is performed in the
stmmac_mdio_unregister() method. It doesn't look good because the handler
isn't originally created in the corresponding protagonist
stmmac_mdio_unregister(), but in the stmmac_xpcs_setup() function. In
order to have more coherent MDIO and XPCS setup/cleanup procedures,
let's move the DW XPCS destruction to the dedicated stmmac_pcs_clean()
method.

This method will also be used to cleanup PCS hardware using the
pcs_exit() callback that will be introduced to stmmac in a subsequent
patch.

Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Co-developed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
---
 drivers/net/ethernet/stmicro/stmmac/stmmac.h      |  1 +
 drivers/net/ethernet/stmicro/stmmac/stmmac_main.c |  6 +++++-
 drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c | 12 +++++++++---
 3 files changed, 15 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
index dddcaa9220cc3..7e0d727ed795b 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
@@ -361,6 +361,7 @@ int stmmac_mdio_unregister(struct net_device *ndev);
 int stmmac_mdio_register(struct net_device *ndev);
 int stmmac_mdio_reset(struct mii_bus *mii);
 int stmmac_xpcs_setup(struct mii_bus *mii);
+void stmmac_pcs_clean(struct stmmac_priv *priv);
 void stmmac_set_ethtool_ops(struct net_device *netdev);
 
 int stmmac_init_tstamp_counter(struct stmmac_priv *priv, u32 systime_flags);
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 59bf83904b62d..2a55c5d07f6b8 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -7789,8 +7789,9 @@ int stmmac_dvr_probe(struct device *device,
 
 error_netdev_register:
 	phylink_destroy(priv->phylink);
-error_xpcs_setup:
 error_phy_setup:
+	stmmac_pcs_clean(priv);
+error_xpcs_setup:
 	if (priv->hw->pcs != STMMAC_PCS_TBI &&
 	    priv->hw->pcs != STMMAC_PCS_RTBI)
 		stmmac_mdio_unregister(ndev);
@@ -7832,6 +7833,9 @@ void stmmac_dvr_remove(struct device *dev)
 	if (priv->plat->stmmac_rst)
 		reset_control_assert(priv->plat->stmmac_rst);
 	reset_control_assert(priv->plat->stmmac_ahb_rst);
+
+	stmmac_pcs_clean(priv);
+
 	if (priv->hw->pcs != STMMAC_PCS_TBI &&
 	    priv->hw->pcs != STMMAC_PCS_RTBI)
 		stmmac_mdio_unregister(ndev);
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
index 0542cfd1817e6..508bd39cbe2b3 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
@@ -523,6 +523,15 @@ int stmmac_xpcs_setup(struct mii_bus *bus)
 	return 0;
 }
 
+void stmmac_pcs_clean(struct stmmac_priv *priv)
+{
+	if (!priv->hw->xpcs)
+		return;
+
+	xpcs_destroy(priv->hw->xpcs);
+	priv->hw->xpcs = NULL;
+}
+
 /**
  * stmmac_mdio_register
  * @ndev: net device structure
@@ -679,9 +688,6 @@ int stmmac_mdio_unregister(struct net_device *ndev)
 	if (!priv->mii)
 		return 0;
 
-	if (priv->hw->xpcs)
-		xpcs_destroy(priv->hw->xpcs);
-
 	mdiobus_unregister(priv->mii);
 	priv->mii->priv = NULL;
 	mdiobus_free(priv->mii);

-- 
2.44.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH net-next v5 3/7] net: stmmac: Make stmmac_xpcs_setup() generic to all PCS devices

[Romain Gantois]

From: Serge Semin <fancer.lancer@gmail.com>

A pcs_init() callback will be introduced to stmmac in a future patch. This
new function will be called during the hardware initialization phase.
Instead of separately initializing XPCS and PCS components, let's group all
PCS-related hardware initialization logic in the current
stmmac_xpcs_setup() function.

Rename stmmac_xpcs_setup() to stmmac_pcs_setup() and move the conditional
call to stmmac_xpcs_setup() inside the function itself.

Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Co-developed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
---
 drivers/net/ethernet/stmicro/stmmac/stmmac.h      |  2 +-
 drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 10 ++++----
 drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c | 28 ++++++++++++++---------
 3 files changed, 22 insertions(+), 18 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
index 7e0d727ed795b..f275f2fd91c3e 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
@@ -360,7 +360,7 @@ enum stmmac_state {
 int stmmac_mdio_unregister(struct net_device *ndev);
 int stmmac_mdio_register(struct net_device *ndev);
 int stmmac_mdio_reset(struct mii_bus *mii);
-int stmmac_xpcs_setup(struct mii_bus *mii);
+int stmmac_pcs_setup(struct net_device *ndev);
 void stmmac_pcs_clean(struct stmmac_priv *priv);
 void stmmac_set_ethtool_ops(struct net_device *netdev);
 
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 2a55c5d07f6b8..72f4deda76407 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -7754,11 +7754,9 @@ int stmmac_dvr_probe(struct device *device,
 	if (priv->plat->speed_mode_2500)
 		priv->plat->speed_mode_2500(ndev, priv->plat->bsp_priv);
 
-	if (priv->plat->mdio_bus_data && priv->plat->mdio_bus_data->has_xpcs) {
-		ret = stmmac_xpcs_setup(priv->mii);
-		if (ret)
-			goto error_xpcs_setup;
-	}
+	ret = stmmac_pcs_setup(ndev);
+	if (ret)
+		goto error_pcs_setup;
 
 	ret = stmmac_phy_setup(priv);
 	if (ret) {
@@ -7791,7 +7789,7 @@ int stmmac_dvr_probe(struct device *device,
 	phylink_destroy(priv->phylink);
 error_phy_setup:
 	stmmac_pcs_clean(priv);
-error_xpcs_setup:
+error_pcs_setup:
 	if (priv->hw->pcs != STMMAC_PCS_TBI &&
 	    priv->hw->pcs != STMMAC_PCS_RTBI)
 		stmmac_mdio_unregister(ndev);
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
index 508bd39cbe2b3..af8ad9768da10 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
@@ -495,31 +495,37 @@ int stmmac_mdio_reset(struct mii_bus *bus)
 	return 0;
 }
 
-int stmmac_xpcs_setup(struct mii_bus *bus)
+int stmmac_pcs_setup(struct net_device *ndev)
 {
-	struct net_device *ndev = bus->priv;
 	struct stmmac_priv *priv;
 	struct dw_xpcs *xpcs;
+	int ret = -ENODEV;
 	int mode, addr;
 
 	priv = netdev_priv(ndev);
 	mode = priv->plat->phy_interface;
 
-	/* Try to probe the XPCS by scanning all addresses. */
-	for (addr = 0; addr < PHY_MAX_ADDR; addr++) {
-		xpcs = xpcs_create_mdiodev(bus, addr, mode);
-		if (IS_ERR(xpcs))
-			continue;
+	if (priv->plat->mdio_bus_data && priv->plat->mdio_bus_data->has_xpcs) {
+		/* Try to probe the XPCS by scanning all addresses */
+		for (addr = 0; addr < PHY_MAX_ADDR; addr++) {
+			xpcs = xpcs_create_mdiodev(priv->mii, addr, mode);
+			if (IS_ERR(xpcs))
+				continue;
 
-		priv->hw->xpcs = xpcs;
-		break;
+			ret = 0;
+			break;
+		}
+	} else {
+		return 0;
 	}
 
-	if (!priv->hw->xpcs) {
+	if (ret) {
 		dev_warn(priv->device, "No xPCS found\n");
-		return -ENODEV;
+		return ret;
 	}
 
+	priv->hw->xpcs = xpcs;
+
 	return 0;
 }
 

-- 
2.44.0

[PATCH net-next v5 3/7] net: stmmac: Make stmmac_xpcs_setup() generic to all PCS devices

[Romain Gantois]

From: Serge Semin <fancer.lancer@gmail.com>

A pcs_init() callback will be introduced to stmmac in a future patch. This
new function will be called during the hardware initialization phase.
Instead of separately initializing XPCS and PCS components, let's group all
PCS-related hardware initialization logic in the current
stmmac_xpcs_setup() function.

Rename stmmac_xpcs_setup() to stmmac_pcs_setup() and move the conditional
call to stmmac_xpcs_setup() inside the function itself.

Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Co-developed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
---
 drivers/net/ethernet/stmicro/stmmac/stmmac.h      |  2 +-
 drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 10 ++++----
 drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c | 28 ++++++++++++++---------
 3 files changed, 22 insertions(+), 18 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
index 7e0d727ed795b..f275f2fd91c3e 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
@@ -360,7 +360,7 @@ enum stmmac_state {
 int stmmac_mdio_unregister(struct net_device *ndev);
 int stmmac_mdio_register(struct net_device *ndev);
 int stmmac_mdio_reset(struct mii_bus *mii);
-int stmmac_xpcs_setup(struct mii_bus *mii);
+int stmmac_pcs_setup(struct net_device *ndev);
 void stmmac_pcs_clean(struct stmmac_priv *priv);
 void stmmac_set_ethtool_ops(struct net_device *netdev);
 
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 2a55c5d07f6b8..72f4deda76407 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -7754,11 +7754,9 @@ int stmmac_dvr_probe(struct device *device,
 	if (priv->plat->speed_mode_2500)
 		priv->plat->speed_mode_2500(ndev, priv->plat->bsp_priv);
 
-	if (priv->plat->mdio_bus_data && priv->plat->mdio_bus_data->has_xpcs) {
-		ret = stmmac_xpcs_setup(priv->mii);
-		if (ret)
-			goto error_xpcs_setup;
-	}
+	ret = stmmac_pcs_setup(ndev);
+	if (ret)
+		goto error_pcs_setup;
 
 	ret = stmmac_phy_setup(priv);
 	if (ret) {
@@ -7791,7 +7789,7 @@ int stmmac_dvr_probe(struct device *device,
 	phylink_destroy(priv->phylink);
 error_phy_setup:
 	stmmac_pcs_clean(priv);
-error_xpcs_setup:
+error_pcs_setup:
 	if (priv->hw->pcs != STMMAC_PCS_TBI &&
 	    priv->hw->pcs != STMMAC_PCS_RTBI)
 		stmmac_mdio_unregister(ndev);
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
index 508bd39cbe2b3..af8ad9768da10 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
@@ -495,31 +495,37 @@ int stmmac_mdio_reset(struct mii_bus *bus)
 	return 0;
 }
 
-int stmmac_xpcs_setup(struct mii_bus *bus)
+int stmmac_pcs_setup(struct net_device *ndev)
 {
-	struct net_device *ndev = bus->priv;
 	struct stmmac_priv *priv;
 	struct dw_xpcs *xpcs;
+	int ret = -ENODEV;
 	int mode, addr;
 
 	priv = netdev_priv(ndev);
 	mode = priv->plat->phy_interface;
 
-	/* Try to probe the XPCS by scanning all addresses. */
-	for (addr = 0; addr < PHY_MAX_ADDR; addr++) {
-		xpcs = xpcs_create_mdiodev(bus, addr, mode);
-		if (IS_ERR(xpcs))
-			continue;
+	if (priv->plat->mdio_bus_data && priv->plat->mdio_bus_data->has_xpcs) {
+		/* Try to probe the XPCS by scanning all addresses */
+		for (addr = 0; addr < PHY_MAX_ADDR; addr++) {
+			xpcs = xpcs_create_mdiodev(priv->mii, addr, mode);
+			if (IS_ERR(xpcs))
+				continue;
 
-		priv->hw->xpcs = xpcs;
-		break;
+			ret = 0;
+			break;
+		}
+	} else {
+		return 0;
 	}
 
-	if (!priv->hw->xpcs) {
+	if (ret) {
 		dev_warn(priv->device, "No xPCS found\n");
-		return -ENODEV;
+		return ret;
 	}
 
+	priv->hw->xpcs = xpcs;
+
 	return 0;
 }
 

-- 
2.44.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH net-next v5 4/7] net: stmmac: introduce pcs_init/pcs_exit stmmac operations

[Romain Gantois]

From: "Russell King (Oracle)" <rmk+kernel@armlinux.org.uk>

Introduce a mechanism whereby platforms can create their PCS instances
prior to the network device being published to userspace, but after
some of the core stmmac initialisation has been completed. This means
that the data structures that platforms need will be available.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Co-developed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
---
 drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c | 8 +++++++-
 include/linux/stmmac.h                            | 2 ++
 2 files changed, 9 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
index af8ad9768da10..1c788caea0cfb 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
@@ -505,7 +505,10 @@ int stmmac_pcs_setup(struct net_device *ndev)
 	priv = netdev_priv(ndev);
 	mode = priv->plat->phy_interface;
 
-	if (priv->plat->mdio_bus_data && priv->plat->mdio_bus_data->has_xpcs) {
+	if (priv->plat->pcs_init) {
+		ret = priv->plat->pcs_init(priv);
+	} else if (priv->plat->mdio_bus_data &&
+		   priv->plat->mdio_bus_data->has_xpcs) {
 		/* Try to probe the XPCS by scanning all addresses */
 		for (addr = 0; addr < PHY_MAX_ADDR; addr++) {
 			xpcs = xpcs_create_mdiodev(priv->mii, addr, mode);
@@ -531,6 +534,9 @@ int stmmac_pcs_setup(struct net_device *ndev)
 
 void stmmac_pcs_clean(struct stmmac_priv *priv)
 {
+	if (priv->plat->pcs_exit)
+		priv->plat->pcs_exit(priv);
+
 	if (!priv->hw->xpcs)
 		return;
 
diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h
index dfa1828cd756a..4a24a246c617d 100644
--- a/include/linux/stmmac.h
+++ b/include/linux/stmmac.h
@@ -285,6 +285,8 @@ struct plat_stmmacenet_data {
 	int (*crosststamp)(ktime_t *device, struct system_counterval_t *system,
 			   void *ctx);
 	void (*dump_debug_regs)(void *priv);
+	int (*pcs_init)(struct stmmac_priv *priv);
+	void (*pcs_exit)(struct stmmac_priv *priv);
 	void *bsp_priv;
 	struct clk *stmmac_clk;
 	struct clk *pclk;

-- 
2.44.0

[PATCH net-next v5 4/7] net: stmmac: introduce pcs_init/pcs_exit stmmac operations

[Romain Gantois]

From: "Russell King (Oracle)" <rmk+kernel@armlinux.org.uk>

Introduce a mechanism whereby platforms can create their PCS instances
prior to the network device being published to userspace, but after
some of the core stmmac initialisation has been completed. This means
that the data structures that platforms need will be available.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Co-developed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
---
 drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c | 8 +++++++-
 include/linux/stmmac.h                            | 2 ++
 2 files changed, 9 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
index af8ad9768da10..1c788caea0cfb 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
@@ -505,7 +505,10 @@ int stmmac_pcs_setup(struct net_device *ndev)
 	priv = netdev_priv(ndev);
 	mode = priv->plat->phy_interface;
 
-	if (priv->plat->mdio_bus_data && priv->plat->mdio_bus_data->has_xpcs) {
+	if (priv->plat->pcs_init) {
+		ret = priv->plat->pcs_init(priv);
+	} else if (priv->plat->mdio_bus_data &&
+		   priv->plat->mdio_bus_data->has_xpcs) {
 		/* Try to probe the XPCS by scanning all addresses */
 		for (addr = 0; addr < PHY_MAX_ADDR; addr++) {
 			xpcs = xpcs_create_mdiodev(priv->mii, addr, mode);
@@ -531,6 +534,9 @@ int stmmac_pcs_setup(struct net_device *ndev)
 
 void stmmac_pcs_clean(struct stmmac_priv *priv)
 {
+	if (priv->plat->pcs_exit)
+		priv->plat->pcs_exit(priv);
+
 	if (!priv->hw->xpcs)
 		return;
 
diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h
index dfa1828cd756a..4a24a246c617d 100644
--- a/include/linux/stmmac.h
+++ b/include/linux/stmmac.h
@@ -285,6 +285,8 @@ struct plat_stmmacenet_data {
 	int (*crosststamp)(ktime_t *device, struct system_counterval_t *system,
 			   void *ctx);
 	void (*dump_debug_regs)(void *priv);
+	int (*pcs_init)(struct stmmac_priv *priv);
+	void (*pcs_exit)(struct stmmac_priv *priv);
 	void *bsp_priv;
 	struct clk *stmmac_clk;
 	struct clk *pclk;

-- 
2.44.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH net-next v5 5/7] net: stmmac: dwmac-socfpga: use pcs_init/pcs_exit

[Romain Gantois]

From: "Russell King (Oracle)" <rmk+kernel@armlinux.org.uk>

Use the newly introduced pcs_init() and pcs_exit() operations to
create and destroy the PCS instance at a more appropriate moment during
the driver lifecycle, thereby avoiding publishing a network device to
userspace that has not yet finished its PCS initialisation.

There are other similar issues with this driver which remain
unaddressed, but these are out of scope for this patch.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
[rgantois: removed second parameters of new callbacks]
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
---
 .../net/ethernet/stmicro/stmmac/dwmac-socfpga.c    | 107 ++++++++++-----------
 1 file changed, 53 insertions(+), 54 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c
index 12b4a80ea3aa1..b3d45f9dfb556 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c
@@ -379,6 +379,56 @@ static int socfpga_gen10_set_phy_mode(struct socfpga_dwmac *dwmac)
 	return 0;
 }
 
+static int socfpga_dwmac_pcs_init(struct stmmac_priv *priv)
+{
+	struct socfpga_dwmac *dwmac = priv->plat->bsp_priv;
+	struct regmap_config pcs_regmap_cfg = {
+		.reg_bits = 16,
+		.val_bits = 16,
+		.reg_shift = REGMAP_UPSHIFT(1),
+	};
+	struct mdio_regmap_config mrc;
+	struct regmap *pcs_regmap;
+	struct phylink_pcs *pcs;
+	struct mii_bus *pcs_bus;
+
+	if (!dwmac->tse_pcs_base)
+		return 0;
+
+	pcs_regmap = devm_regmap_init_mmio(priv->device, dwmac->tse_pcs_base,
+					   &pcs_regmap_cfg);
+	if (IS_ERR(pcs_regmap))
+		return PTR_ERR(pcs_regmap);
+
+	memset(&mrc, 0, sizeof(mrc));
+	mrc.regmap = pcs_regmap;
+	mrc.parent = priv->device;
+	mrc.valid_addr = 0x0;
+	mrc.autoscan = false;
+
+	/* Can't use ndev->name here because it will not have been initialised,
+	 * and in any case, the user can rename network interfaces at runtime.
+	 */
+	snprintf(mrc.name, MII_BUS_ID_SIZE, "%s-pcs-mii",
+		 dev_name(priv->device));
+	pcs_bus = devm_mdio_regmap_register(priv->device, &mrc);
+	if (IS_ERR(pcs_bus))
+		return PTR_ERR(pcs_bus);
+
+	pcs = lynx_pcs_create_mdiodev(pcs_bus, 0);
+	if (IS_ERR(pcs))
+		return PTR_ERR(pcs);
+
+	priv->hw->phylink_pcs = pcs;
+	return 0;
+}
+
+static void socfpga_dwmac_pcs_exit(struct stmmac_priv *priv)
+{
+	if (priv->hw->phylink_pcs)
+		lynx_pcs_destroy(priv->hw->phylink_pcs);
+}
+
 static int socfpga_dwmac_probe(struct platform_device *pdev)
 {
 	struct plat_stmmacenet_data *plat_dat;
@@ -426,6 +476,8 @@ static int socfpga_dwmac_probe(struct platform_device *pdev)
 	dwmac->ops = ops;
 	plat_dat->bsp_priv = dwmac;
 	plat_dat->fix_mac_speed = socfpga_dwmac_fix_mac_speed;
+	plat_dat->pcs_init = socfpga_dwmac_pcs_init;
+	plat_dat->pcs_exit = socfpga_dwmac_pcs_exit;
 
 	ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
 	if (ret)
@@ -444,48 +496,6 @@ static int socfpga_dwmac_probe(struct platform_device *pdev)
 	if (ret)
 		goto err_dvr_remove;
 
-	/* Create a regmap for the PCS so that it can be used by the PCS driver,
-	 * if we have such a PCS
-	 */
-	if (dwmac->tse_pcs_base) {
-		struct regmap_config pcs_regmap_cfg;
-		struct mdio_regmap_config mrc;
-		struct regmap *pcs_regmap;
-		struct mii_bus *pcs_bus;
-
-		memset(&pcs_regmap_cfg, 0, sizeof(pcs_regmap_cfg));
-		memset(&mrc, 0, sizeof(mrc));
-
-		pcs_regmap_cfg.reg_bits = 16;
-		pcs_regmap_cfg.val_bits = 16;
-		pcs_regmap_cfg.reg_shift = REGMAP_UPSHIFT(1);
-
-		pcs_regmap = devm_regmap_init_mmio(&pdev->dev, dwmac->tse_pcs_base,
-						   &pcs_regmap_cfg);
-		if (IS_ERR(pcs_regmap)) {
-			ret = PTR_ERR(pcs_regmap);
-			goto err_dvr_remove;
-		}
-
-		mrc.regmap = pcs_regmap;
-		mrc.parent = &pdev->dev;
-		mrc.valid_addr = 0x0;
-		mrc.autoscan = false;
-
-		snprintf(mrc.name, MII_BUS_ID_SIZE, "%s-pcs-mii", ndev->name);
-		pcs_bus = devm_mdio_regmap_register(&pdev->dev, &mrc);
-		if (IS_ERR(pcs_bus)) {
-			ret = PTR_ERR(pcs_bus);
-			goto err_dvr_remove;
-		}
-
-		stpriv->hw->phylink_pcs = lynx_pcs_create_mdiodev(pcs_bus, 0);
-		if (IS_ERR(stpriv->hw->phylink_pcs)) {
-			ret = PTR_ERR(stpriv->hw->phylink_pcs);
-			goto err_dvr_remove;
-		}
-	}
-
 	return 0;
 
 err_dvr_remove:
@@ -494,17 +504,6 @@ static int socfpga_dwmac_probe(struct platform_device *pdev)
 	return ret;
 }
 
-static void socfpga_dwmac_remove(struct platform_device *pdev)
-{
-	struct net_device *ndev = platform_get_drvdata(pdev);
-	struct stmmac_priv *priv = netdev_priv(ndev);
-	struct phylink_pcs *pcs = priv->hw->phylink_pcs;
-
-	stmmac_pltfr_remove(pdev);
-
-	lynx_pcs_destroy(pcs);
-}
-
 #ifdef CONFIG_PM_SLEEP
 static int socfpga_dwmac_resume(struct device *dev)
 {
@@ -576,7 +575,7 @@ MODULE_DEVICE_TABLE(of, socfpga_dwmac_match);
 
 static struct platform_driver socfpga_dwmac_driver = {
 	.probe  = socfpga_dwmac_probe,
-	.remove_new = socfpga_dwmac_remove,
+	.remove_new = stmmac_pltfr_remove,
 	.driver = {
 		.name           = "socfpga-dwmac",
 		.pm		= &socfpga_dwmac_pm_ops,

-- 
2.44.0

[PATCH net-next v5 5/7] net: stmmac: dwmac-socfpga: use pcs_init/pcs_exit

[Romain Gantois]

From: "Russell King (Oracle)" <rmk+kernel@armlinux.org.uk>

Use the newly introduced pcs_init() and pcs_exit() operations to
create and destroy the PCS instance at a more appropriate moment during
the driver lifecycle, thereby avoiding publishing a network device to
userspace that has not yet finished its PCS initialisation.

There are other similar issues with this driver which remain
unaddressed, but these are out of scope for this patch.

Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
[rgantois: removed second parameters of new callbacks]
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
---
 .../net/ethernet/stmicro/stmmac/dwmac-socfpga.c    | 107 ++++++++++-----------
 1 file changed, 53 insertions(+), 54 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c
index 12b4a80ea3aa1..b3d45f9dfb556 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c
@@ -379,6 +379,56 @@ static int socfpga_gen10_set_phy_mode(struct socfpga_dwmac *dwmac)
 	return 0;
 }
 
+static int socfpga_dwmac_pcs_init(struct stmmac_priv *priv)
+{
+	struct socfpga_dwmac *dwmac = priv->plat->bsp_priv;
+	struct regmap_config pcs_regmap_cfg = {
+		.reg_bits = 16,
+		.val_bits = 16,
+		.reg_shift = REGMAP_UPSHIFT(1),
+	};
+	struct mdio_regmap_config mrc;
+	struct regmap *pcs_regmap;
+	struct phylink_pcs *pcs;
+	struct mii_bus *pcs_bus;
+
+	if (!dwmac->tse_pcs_base)
+		return 0;
+
+	pcs_regmap = devm_regmap_init_mmio(priv->device, dwmac->tse_pcs_base,
+					   &pcs_regmap_cfg);
+	if (IS_ERR(pcs_regmap))
+		return PTR_ERR(pcs_regmap);
+
+	memset(&mrc, 0, sizeof(mrc));
+	mrc.regmap = pcs_regmap;
+	mrc.parent = priv->device;
+	mrc.valid_addr = 0x0;
+	mrc.autoscan = false;
+
+	/* Can't use ndev->name here because it will not have been initialised,
+	 * and in any case, the user can rename network interfaces at runtime.
+	 */
+	snprintf(mrc.name, MII_BUS_ID_SIZE, "%s-pcs-mii",
+		 dev_name(priv->device));
+	pcs_bus = devm_mdio_regmap_register(priv->device, &mrc);
+	if (IS_ERR(pcs_bus))
+		return PTR_ERR(pcs_bus);
+
+	pcs = lynx_pcs_create_mdiodev(pcs_bus, 0);
+	if (IS_ERR(pcs))
+		return PTR_ERR(pcs);
+
+	priv->hw->phylink_pcs = pcs;
+	return 0;
+}
+
+static void socfpga_dwmac_pcs_exit(struct stmmac_priv *priv)
+{
+	if (priv->hw->phylink_pcs)
+		lynx_pcs_destroy(priv->hw->phylink_pcs);
+}
+
 static int socfpga_dwmac_probe(struct platform_device *pdev)
 {
 	struct plat_stmmacenet_data *plat_dat;
@@ -426,6 +476,8 @@ static int socfpga_dwmac_probe(struct platform_device *pdev)
 	dwmac->ops = ops;
 	plat_dat->bsp_priv = dwmac;
 	plat_dat->fix_mac_speed = socfpga_dwmac_fix_mac_speed;
+	plat_dat->pcs_init = socfpga_dwmac_pcs_init;
+	plat_dat->pcs_exit = socfpga_dwmac_pcs_exit;
 
 	ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
 	if (ret)
@@ -444,48 +496,6 @@ static int socfpga_dwmac_probe(struct platform_device *pdev)
 	if (ret)
 		goto err_dvr_remove;
 
-	/* Create a regmap for the PCS so that it can be used by the PCS driver,
-	 * if we have such a PCS
-	 */
-	if (dwmac->tse_pcs_base) {
-		struct regmap_config pcs_regmap_cfg;
-		struct mdio_regmap_config mrc;
-		struct regmap *pcs_regmap;
-		struct mii_bus *pcs_bus;
-
-		memset(&pcs_regmap_cfg, 0, sizeof(pcs_regmap_cfg));
-		memset(&mrc, 0, sizeof(mrc));
-
-		pcs_regmap_cfg.reg_bits = 16;
-		pcs_regmap_cfg.val_bits = 16;
-		pcs_regmap_cfg.reg_shift = REGMAP_UPSHIFT(1);
-
-		pcs_regmap = devm_regmap_init_mmio(&pdev->dev, dwmac->tse_pcs_base,
-						   &pcs_regmap_cfg);
-		if (IS_ERR(pcs_regmap)) {
-			ret = PTR_ERR(pcs_regmap);
-			goto err_dvr_remove;
-		}
-
-		mrc.regmap = pcs_regmap;
-		mrc.parent = &pdev->dev;
-		mrc.valid_addr = 0x0;
-		mrc.autoscan = false;
-
-		snprintf(mrc.name, MII_BUS_ID_SIZE, "%s-pcs-mii", ndev->name);
-		pcs_bus = devm_mdio_regmap_register(&pdev->dev, &mrc);
-		if (IS_ERR(pcs_bus)) {
-			ret = PTR_ERR(pcs_bus);
-			goto err_dvr_remove;
-		}
-
-		stpriv->hw->phylink_pcs = lynx_pcs_create_mdiodev(pcs_bus, 0);
-		if (IS_ERR(stpriv->hw->phylink_pcs)) {
-			ret = PTR_ERR(stpriv->hw->phylink_pcs);
-			goto err_dvr_remove;
-		}
-	}
-
 	return 0;
 
 err_dvr_remove:
@@ -494,17 +504,6 @@ static int socfpga_dwmac_probe(struct platform_device *pdev)
 	return ret;
 }
 
-static void socfpga_dwmac_remove(struct platform_device *pdev)
-{
-	struct net_device *ndev = platform_get_drvdata(pdev);
-	struct stmmac_priv *priv = netdev_priv(ndev);
-	struct phylink_pcs *pcs = priv->hw->phylink_pcs;
-
-	stmmac_pltfr_remove(pdev);
-
-	lynx_pcs_destroy(pcs);
-}
-
 #ifdef CONFIG_PM_SLEEP
 static int socfpga_dwmac_resume(struct device *dev)
 {
@@ -576,7 +575,7 @@ MODULE_DEVICE_TABLE(of, socfpga_dwmac_match);
 
 static struct platform_driver socfpga_dwmac_driver = {
 	.probe  = socfpga_dwmac_probe,
-	.remove_new = socfpga_dwmac_remove,
+	.remove_new = stmmac_pltfr_remove,
 	.driver = {
 		.name           = "socfpga-dwmac",
 		.pm		= &socfpga_dwmac_pm_ops,

-- 
2.44.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH net-next v5 6/7] net: stmmac: add support for RZ/N1 GMAC

[Romain Gantois]

From: Clément Léger <clement.leger@bootlin.com>

Add support for the Renesas RZ/N1 GMAC. This support can make use of a
custom RZ/N1 PCS which is fetched by parsing the pcs-handle device tree
property.

Signed-off-by: "Clément Léger" <clement.leger@bootlin.com>
Co-developed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
---
 MAINTAINERS                                      |  6 ++
 drivers/net/ethernet/stmicro/stmmac/Kconfig      | 12 ++++
 drivers/net/ethernet/stmicro/stmmac/Makefile     |  1 +
 drivers/net/ethernet/stmicro/stmmac/dwmac-rzn1.c | 86 ++++++++++++++++++++++++
 4 files changed, 105 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 943921d642add..b65e9908f8532 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -18876,6 +18876,12 @@ F:	include/dt-bindings/net/pcs-rzn1-miic.h
 F:	include/linux/pcs-rzn1-miic.h
 F:	net/dsa/tag_rzn1_a5psw.c
 
+RENESAS RZ/N1 DWMAC GLUE LAYER
+M:	Romain Gantois <romain.gantois@bootlin.com>
+S:	Maintained
+F:	Documentation/devicetree/bindings/net/renesas,rzn1-gmac.yaml
+F:	drivers/net/ethernet/stmicro/stmmac/dwmac-rzn1.c
+
 RENESAS RZ/N1 RTC CONTROLLER DRIVER
 M:	Miquel Raynal <miquel.raynal@bootlin.com>
 L:	linux-rtc@vger.kernel.org
diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
index 4ec61f1ee71a2..05cc07b8f48c0 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
+++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
@@ -142,6 +142,18 @@ config DWMAC_ROCKCHIP
 	  This selects the Rockchip RK3288 SoC glue layer support for
 	  the stmmac device driver.
 
+config DWMAC_RZN1
+	tristate "Renesas RZ/N1 dwmac support"
+	default ARCH_RZN1
+	depends on OF && (ARCH_RZN1 || COMPILE_TEST)
+	select PCS_RZN1_MIIC
+	help
+	  Support for Ethernet controller on Renesas RZ/N1 SoC family.
+
+	  This selects the Renesas RZ/N1 SoC glue layer support for
+	  the stmmac device driver. This support can make use of a custom MII
+	  converter PCS device.
+
 config DWMAC_SOCFPGA
 	tristate "SOCFPGA dwmac support"
 	default ARCH_INTEL_SOCFPGA
diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile
index 26cad4344701e..c2f0e91f6bf83 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Makefile
+++ b/drivers/net/ethernet/stmicro/stmmac/Makefile
@@ -21,6 +21,7 @@ obj-$(CONFIG_DWMAC_MEDIATEK)	+= dwmac-mediatek.o
 obj-$(CONFIG_DWMAC_MESON)	+= dwmac-meson.o dwmac-meson8b.o
 obj-$(CONFIG_DWMAC_QCOM_ETHQOS)	+= dwmac-qcom-ethqos.o
 obj-$(CONFIG_DWMAC_ROCKCHIP)	+= dwmac-rk.o
+obj-$(CONFIG_DWMAC_RZN1)	+= dwmac-rzn1.o
 obj-$(CONFIG_DWMAC_SOCFPGA)	+= dwmac-altr-socfpga.o
 obj-$(CONFIG_DWMAC_STARFIVE)	+= dwmac-starfive.o
 obj-$(CONFIG_DWMAC_STI)		+= dwmac-sti.o
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-rzn1.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-rzn1.c
new file mode 100644
index 0000000000000..848cf3c01f4ab
--- /dev/null
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-rzn1.c
@@ -0,0 +1,86 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2024 Schneider-Electric
+ *
+ * Clément Léger <clement.leger@bootlin.com>
+ */
+
+#include <linux/of.h>
+#include <linux/pcs-rzn1-miic.h>
+#include <linux/phylink.h>
+#include <linux/platform_device.h>
+
+#include "stmmac_platform.h"
+#include "stmmac.h"
+
+static int rzn1_dwmac_pcs_init(struct stmmac_priv *priv)
+{
+	struct device_node *np = priv->device->of_node;
+	struct device_node *pcs_node;
+	struct phylink_pcs *pcs;
+
+	pcs_node = of_parse_phandle(np, "pcs-handle", 0);
+
+	if (pcs_node) {
+		pcs = miic_create(priv->device, pcs_node);
+		of_node_put(pcs_node);
+		if (IS_ERR(pcs))
+			return PTR_ERR(pcs);
+
+		priv->hw->phylink_pcs = pcs;
+	}
+
+	return 0;
+}
+
+static void rzn1_dwmac_pcs_exit(struct stmmac_priv *priv)
+{
+	if (priv->hw->phylink_pcs)
+		miic_destroy(priv->hw->phylink_pcs);
+}
+
+static int rzn1_dwmac_probe(struct platform_device *pdev)
+{
+	struct plat_stmmacenet_data *plat_dat;
+	struct stmmac_resources stmmac_res;
+	struct device *dev = &pdev->dev;
+	int ret;
+
+	ret = stmmac_get_platform_resources(pdev, &stmmac_res);
+	if (ret)
+		return ret;
+
+	plat_dat = devm_stmmac_probe_config_dt(pdev, stmmac_res.mac);
+	if (IS_ERR(plat_dat))
+		return PTR_ERR(plat_dat);
+
+	plat_dat->bsp_priv = plat_dat;
+	plat_dat->pcs_init = rzn1_dwmac_pcs_init;
+	plat_dat->pcs_exit = rzn1_dwmac_pcs_exit;
+
+	ret = stmmac_dvr_probe(dev, plat_dat, &stmmac_res);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static const struct of_device_id rzn1_dwmac_match[] = {
+	{ .compatible = "renesas,rzn1-gmac" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, rzn1_dwmac_match);
+
+static struct platform_driver rzn1_dwmac_driver = {
+	.probe  = rzn1_dwmac_probe,
+	.remove_new = stmmac_pltfr_remove,
+	.driver = {
+		.name           = "rzn1-dwmac",
+		.of_match_table = rzn1_dwmac_match,
+	},
+};
+module_platform_driver(rzn1_dwmac_driver);
+
+MODULE_AUTHOR("Clément Léger <clement.leger@bootlin.com>");
+MODULE_DESCRIPTION("Renesas RZN1 DWMAC specific glue layer");
+MODULE_LICENSE("GPL");

-- 
2.44.0

[PATCH net-next v5 6/7] net: stmmac: add support for RZ/N1 GMAC

[Romain Gantois]

From: Clément Léger <clement.leger@bootlin.com>

Add support for the Renesas RZ/N1 GMAC. This support can make use of a
custom RZ/N1 PCS which is fetched by parsing the pcs-handle device tree
property.

Signed-off-by: "Clément Léger" <clement.leger@bootlin.com>
Co-developed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
---
 MAINTAINERS                                      |  6 ++
 drivers/net/ethernet/stmicro/stmmac/Kconfig      | 12 ++++
 drivers/net/ethernet/stmicro/stmmac/Makefile     |  1 +
 drivers/net/ethernet/stmicro/stmmac/dwmac-rzn1.c | 86 ++++++++++++++++++++++++
 4 files changed, 105 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 943921d642add..b65e9908f8532 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -18876,6 +18876,12 @@ F:	include/dt-bindings/net/pcs-rzn1-miic.h
 F:	include/linux/pcs-rzn1-miic.h
 F:	net/dsa/tag_rzn1_a5psw.c
 
+RENESAS RZ/N1 DWMAC GLUE LAYER
+M:	Romain Gantois <romain.gantois@bootlin.com>
+S:	Maintained
+F:	Documentation/devicetree/bindings/net/renesas,rzn1-gmac.yaml
+F:	drivers/net/ethernet/stmicro/stmmac/dwmac-rzn1.c
+
 RENESAS RZ/N1 RTC CONTROLLER DRIVER
 M:	Miquel Raynal <miquel.raynal@bootlin.com>
 L:	linux-rtc@vger.kernel.org
diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
index 4ec61f1ee71a2..05cc07b8f48c0 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
+++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
@@ -142,6 +142,18 @@ config DWMAC_ROCKCHIP
 	  This selects the Rockchip RK3288 SoC glue layer support for
 	  the stmmac device driver.
 
+config DWMAC_RZN1
+	tristate "Renesas RZ/N1 dwmac support"
+	default ARCH_RZN1
+	depends on OF && (ARCH_RZN1 || COMPILE_TEST)
+	select PCS_RZN1_MIIC
+	help
+	  Support for Ethernet controller on Renesas RZ/N1 SoC family.
+
+	  This selects the Renesas RZ/N1 SoC glue layer support for
+	  the stmmac device driver. This support can make use of a custom MII
+	  converter PCS device.
+
 config DWMAC_SOCFPGA
 	tristate "SOCFPGA dwmac support"
 	default ARCH_INTEL_SOCFPGA
diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile
index 26cad4344701e..c2f0e91f6bf83 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Makefile
+++ b/drivers/net/ethernet/stmicro/stmmac/Makefile
@@ -21,6 +21,7 @@ obj-$(CONFIG_DWMAC_MEDIATEK)	+= dwmac-mediatek.o
 obj-$(CONFIG_DWMAC_MESON)	+= dwmac-meson.o dwmac-meson8b.o
 obj-$(CONFIG_DWMAC_QCOM_ETHQOS)	+= dwmac-qcom-ethqos.o
 obj-$(CONFIG_DWMAC_ROCKCHIP)	+= dwmac-rk.o
+obj-$(CONFIG_DWMAC_RZN1)	+= dwmac-rzn1.o
 obj-$(CONFIG_DWMAC_SOCFPGA)	+= dwmac-altr-socfpga.o
 obj-$(CONFIG_DWMAC_STARFIVE)	+= dwmac-starfive.o
 obj-$(CONFIG_DWMAC_STI)		+= dwmac-sti.o
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-rzn1.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-rzn1.c
new file mode 100644
index 0000000000000..848cf3c01f4ab
--- /dev/null
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-rzn1.c
@@ -0,0 +1,86 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2024 Schneider-Electric
+ *
+ * Clément Léger <clement.leger@bootlin.com>
+ */
+
+#include <linux/of.h>
+#include <linux/pcs-rzn1-miic.h>
+#include <linux/phylink.h>
+#include <linux/platform_device.h>
+
+#include "stmmac_platform.h"
+#include "stmmac.h"
+
+static int rzn1_dwmac_pcs_init(struct stmmac_priv *priv)
+{
+	struct device_node *np = priv->device->of_node;
+	struct device_node *pcs_node;
+	struct phylink_pcs *pcs;
+
+	pcs_node = of_parse_phandle(np, "pcs-handle", 0);
+
+	if (pcs_node) {
+		pcs = miic_create(priv->device, pcs_node);
+		of_node_put(pcs_node);
+		if (IS_ERR(pcs))
+			return PTR_ERR(pcs);
+
+		priv->hw->phylink_pcs = pcs;
+	}
+
+	return 0;
+}
+
+static void rzn1_dwmac_pcs_exit(struct stmmac_priv *priv)
+{
+	if (priv->hw->phylink_pcs)
+		miic_destroy(priv->hw->phylink_pcs);
+}
+
+static int rzn1_dwmac_probe(struct platform_device *pdev)
+{
+	struct plat_stmmacenet_data *plat_dat;
+	struct stmmac_resources stmmac_res;
+	struct device *dev = &pdev->dev;
+	int ret;
+
+	ret = stmmac_get_platform_resources(pdev, &stmmac_res);
+	if (ret)
+		return ret;
+
+	plat_dat = devm_stmmac_probe_config_dt(pdev, stmmac_res.mac);
+	if (IS_ERR(plat_dat))
+		return PTR_ERR(plat_dat);
+
+	plat_dat->bsp_priv = plat_dat;
+	plat_dat->pcs_init = rzn1_dwmac_pcs_init;
+	plat_dat->pcs_exit = rzn1_dwmac_pcs_exit;
+
+	ret = stmmac_dvr_probe(dev, plat_dat, &stmmac_res);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static const struct of_device_id rzn1_dwmac_match[] = {
+	{ .compatible = "renesas,rzn1-gmac" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, rzn1_dwmac_match);
+
+static struct platform_driver rzn1_dwmac_driver = {
+	.probe  = rzn1_dwmac_probe,
+	.remove_new = stmmac_pltfr_remove,
+	.driver = {
+		.name           = "rzn1-dwmac",
+		.of_match_table = rzn1_dwmac_match,
+	},
+};
+module_platform_driver(rzn1_dwmac_driver);
+
+MODULE_AUTHOR("Clément Léger <clement.leger@bootlin.com>");
+MODULE_DESCRIPTION("Renesas RZN1 DWMAC specific glue layer");
+MODULE_LICENSE("GPL");

-- 
2.44.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH net-next v5 7/7] ARM: dts: r9a06g032: describe GMAC1

[Romain Gantois]

From: Clément Léger <clement.leger@bootlin.com>

The r9a06g032 SoC of the RZ/N1 family features two GMAC devices named
GMAC1/2, that are based on Synopsys cores. GMAC1 is connected to a
RGMII/RMII converter that is already described in this device tree.

Signed-off-by: Clément Léger <clement.leger@bootlin.com>
[rgantois: commit log]
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
---
 arch/arm/boot/dts/renesas/r9a06g032.dtsi | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/arch/arm/boot/dts/renesas/r9a06g032.dtsi b/arch/arm/boot/dts/renesas/r9a06g032.dtsi
index fa63e1afc4ef4..57c730f43442e 100644
--- a/arch/arm/boot/dts/renesas/r9a06g032.dtsi
+++ b/arch/arm/boot/dts/renesas/r9a06g032.dtsi
@@ -316,6 +316,24 @@ dma1: dma-controller@40105000 {
 			data-width = <8>;
 		};
 
+		gmac1: ethernet@44000000 {
+			compatible = "renesas,r9a06g032-gmac", "renesas,rzn1-gmac", "snps,dwmac";
+			reg = <0x44000000 0x2000>;
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+			clocks = <&sysctrl R9A06G032_HCLK_GMAC0>;
+			clock-names = "stmmaceth";
+			power-domains = <&sysctrl>;
+			snps,multicast-filter-bins = <256>;
+			snps,perfect-filter-entries = <128>;
+			tx-fifo-depth = <2048>;
+			rx-fifo-depth = <4096>;
+			pcs-handle = <&mii_conv1>;
+			status = "disabled";
+		};
+
 		gmac2: ethernet@44002000 {
 			compatible = "renesas,r9a06g032-gmac", "renesas,rzn1-gmac", "snps,dwmac";
 			reg = <0x44002000 0x2000>;

-- 
2.44.0

[PATCH net-next v5 7/7] ARM: dts: r9a06g032: describe GMAC1

[Romain Gantois]

From: Clément Léger <clement.leger@bootlin.com>

The r9a06g032 SoC of the RZ/N1 family features two GMAC devices named
GMAC1/2, that are based on Synopsys cores. GMAC1 is connected to a
RGMII/RMII converter that is already described in this device tree.

Signed-off-by: Clément Léger <clement.leger@bootlin.com>
[rgantois: commit log]
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
---
 arch/arm/boot/dts/renesas/r9a06g032.dtsi | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/arch/arm/boot/dts/renesas/r9a06g032.dtsi b/arch/arm/boot/dts/renesas/r9a06g032.dtsi
index fa63e1afc4ef4..57c730f43442e 100644
--- a/arch/arm/boot/dts/renesas/r9a06g032.dtsi
+++ b/arch/arm/boot/dts/renesas/r9a06g032.dtsi
@@ -316,6 +316,24 @@ dma1: dma-controller@40105000 {
 			data-width = <8>;
 		};
 
+		gmac1: ethernet@44000000 {
+			compatible = "renesas,r9a06g032-gmac", "renesas,rzn1-gmac", "snps,dwmac";
+			reg = <0x44000000 0x2000>;
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+			clocks = <&sysctrl R9A06G032_HCLK_GMAC0>;
+			clock-names = "stmmaceth";
+			power-domains = <&sysctrl>;
+			snps,multicast-filter-bins = <256>;
+			snps,perfect-filter-entries = <128>;
+			tx-fifo-depth = <2048>;
+			rx-fifo-depth = <4096>;
+			pcs-handle = <&mii_conv1>;
+			status = "disabled";
+		};
+
 		gmac2: ethernet@44002000 {
 			compatible = "renesas,r9a06g032-gmac", "renesas,rzn1-gmac", "snps,dwmac";
 			reg = <0x44002000 0x2000>;

-- 
2.44.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH net-next v5 2/7] net: stmmac: Add dedicated XPCS cleanup method

[Serge Semin]

Hi Romain

On Tue, Apr 30, 2024 at 09:29:42AM +0200, Romain Gantois wrote:
> From: Serge Semin <fancer.lancer@gmail.com>
> 
> Currently the XPCS handler destruction is performed in the
> stmmac_mdio_unregister() method. It doesn't look good because the handler
> isn't originally created in the corresponding protagonist
> stmmac_mdio_unregister(), but in the stmmac_xpcs_setup() function. In
> order to have more coherent MDIO and XPCS setup/cleanup procedures,
> let's move the DW XPCS destruction to the dedicated stmmac_pcs_clean()
> method.
> 
> This method will also be used to cleanup PCS hardware using the
> pcs_exit() callback that will be introduced to stmmac in a subsequent
> patch.
> 
> Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
> Co-developed-by: Romain Gantois <romain.gantois@bootlin.com>
> Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
> ---
>  drivers/net/ethernet/stmicro/stmmac/stmmac.h      |  1 +
>  drivers/net/ethernet/stmicro/stmmac/stmmac_main.c |  6 +++++-
>  drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c | 12 +++++++++---
>  3 files changed, 15 insertions(+), 4 deletions(-)
> 
> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
> index dddcaa9220cc3..7e0d727ed795b 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h
> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
> @@ -361,6 +361,7 @@ int stmmac_mdio_unregister(struct net_device *ndev);
>  int stmmac_mdio_register(struct net_device *ndev);
>  int stmmac_mdio_reset(struct mii_bus *mii);
>  int stmmac_xpcs_setup(struct mii_bus *mii);
> +void stmmac_pcs_clean(struct stmmac_priv *priv);
>  void stmmac_set_ethtool_ops(struct net_device *netdev);
>  
>  int stmmac_init_tstamp_counter(struct stmmac_priv *priv, u32 systime_flags);
> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
> index 59bf83904b62d..2a55c5d07f6b8 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
> @@ -7789,8 +7789,9 @@ int stmmac_dvr_probe(struct device *device,
>  
>  error_netdev_register:
>  	phylink_destroy(priv->phylink);
> -error_xpcs_setup:
>  error_phy_setup:
> +	stmmac_pcs_clean(priv);
> +error_xpcs_setup:
>  	if (priv->hw->pcs != STMMAC_PCS_TBI &&
>  	    priv->hw->pcs != STMMAC_PCS_RTBI)
>  		stmmac_mdio_unregister(ndev);
> @@ -7832,6 +7833,9 @@ void stmmac_dvr_remove(struct device *dev)
>  	if (priv->plat->stmmac_rst)
>  		reset_control_assert(priv->plat->stmmac_rst);
>  	reset_control_assert(priv->plat->stmmac_ahb_rst);
> +
> +	stmmac_pcs_clean(priv);
> +
>  	if (priv->hw->pcs != STMMAC_PCS_TBI &&
>  	    priv->hw->pcs != STMMAC_PCS_RTBI)
>  		stmmac_mdio_unregister(ndev);
> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
> index 0542cfd1817e6..508bd39cbe2b3 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
> @@ -523,6 +523,15 @@ int stmmac_xpcs_setup(struct mii_bus *bus)
>  	return 0;
>  }
>  

> +void stmmac_pcs_clean(struct stmmac_priv *priv)

Ideally it would have been great to have the entire driver fixed to
accept the stmmac_priv pointer as the functions argument. But this
would be too tiresome. Anyway seeing the PCS-setup protagonist method
has the net_device pointer passed I would implement the same prototype
for the antagonist even though it would require an additional local
variable. That will make the MDIO and PCS local interface-functions
looking alike and as if unified. That is the reason of why I made
stmmac_xpcs_clean() accepting the net_device pointer. 

Alternatively both stmmac_pcs_setup() and stmmac_pcs_clean() could be
converted to just accepting a pointer to the stmmac_priv instance.

-Serge(y)

> +{
> +	if (!priv->hw->xpcs)
> +		return;
> +
> +	xpcs_destroy(priv->hw->xpcs);
> +	priv->hw->xpcs = NULL;
> +}
> +
>  /**
>   * stmmac_mdio_register
>   * @ndev: net device structure
> @@ -679,9 +688,6 @@ int stmmac_mdio_unregister(struct net_device *ndev)
>  	if (!priv->mii)
>  		return 0;
>  
> -	if (priv->hw->xpcs)
> -		xpcs_destroy(priv->hw->xpcs);
> -
>  	mdiobus_unregister(priv->mii);
>  	priv->mii->priv = NULL;
>  	mdiobus_free(priv->mii);
> 
> -- 
> 2.44.0
> 

Re: [PATCH net-next v5 2/7] net: stmmac: Add dedicated XPCS cleanup method

[Serge Semin]

Hi Romain

On Tue, Apr 30, 2024 at 09:29:42AM +0200, Romain Gantois wrote:
> From: Serge Semin <fancer.lancer@gmail.com>
> 
> Currently the XPCS handler destruction is performed in the
> stmmac_mdio_unregister() method. It doesn't look good because the handler
> isn't originally created in the corresponding protagonist
> stmmac_mdio_unregister(), but in the stmmac_xpcs_setup() function. In
> order to have more coherent MDIO and XPCS setup/cleanup procedures,
> let's move the DW XPCS destruction to the dedicated stmmac_pcs_clean()
> method.
> 
> This method will also be used to cleanup PCS hardware using the
> pcs_exit() callback that will be introduced to stmmac in a subsequent
> patch.
> 
> Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
> Co-developed-by: Romain Gantois <romain.gantois@bootlin.com>
> Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
> ---
>  drivers/net/ethernet/stmicro/stmmac/stmmac.h      |  1 +
>  drivers/net/ethernet/stmicro/stmmac/stmmac_main.c |  6 +++++-
>  drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c | 12 +++++++++---
>  3 files changed, 15 insertions(+), 4 deletions(-)
> 
> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
> index dddcaa9220cc3..7e0d727ed795b 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h
> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
> @@ -361,6 +361,7 @@ int stmmac_mdio_unregister(struct net_device *ndev);
>  int stmmac_mdio_register(struct net_device *ndev);
>  int stmmac_mdio_reset(struct mii_bus *mii);
>  int stmmac_xpcs_setup(struct mii_bus *mii);
> +void stmmac_pcs_clean(struct stmmac_priv *priv);
>  void stmmac_set_ethtool_ops(struct net_device *netdev);
>  
>  int stmmac_init_tstamp_counter(struct stmmac_priv *priv, u32 systime_flags);
> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
> index 59bf83904b62d..2a55c5d07f6b8 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
> @@ -7789,8 +7789,9 @@ int stmmac_dvr_probe(struct device *device,
>  
>  error_netdev_register:
>  	phylink_destroy(priv->phylink);
> -error_xpcs_setup:
>  error_phy_setup:
> +	stmmac_pcs_clean(priv);
> +error_xpcs_setup:
>  	if (priv->hw->pcs != STMMAC_PCS_TBI &&
>  	    priv->hw->pcs != STMMAC_PCS_RTBI)
>  		stmmac_mdio_unregister(ndev);
> @@ -7832,6 +7833,9 @@ void stmmac_dvr_remove(struct device *dev)
>  	if (priv->plat->stmmac_rst)
>  		reset_control_assert(priv->plat->stmmac_rst);
>  	reset_control_assert(priv->plat->stmmac_ahb_rst);
> +
> +	stmmac_pcs_clean(priv);
> +
>  	if (priv->hw->pcs != STMMAC_PCS_TBI &&
>  	    priv->hw->pcs != STMMAC_PCS_RTBI)
>  		stmmac_mdio_unregister(ndev);
> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
> index 0542cfd1817e6..508bd39cbe2b3 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
> @@ -523,6 +523,15 @@ int stmmac_xpcs_setup(struct mii_bus *bus)
>  	return 0;
>  }
>  

> +void stmmac_pcs_clean(struct stmmac_priv *priv)

Ideally it would have been great to have the entire driver fixed to
accept the stmmac_priv pointer as the functions argument. But this
would be too tiresome. Anyway seeing the PCS-setup protagonist method
has the net_device pointer passed I would implement the same prototype
for the antagonist even though it would require an additional local
variable. That will make the MDIO and PCS local interface-functions
looking alike and as if unified. That is the reason of why I made
stmmac_xpcs_clean() accepting the net_device pointer. 

Alternatively both stmmac_pcs_setup() and stmmac_pcs_clean() could be
converted to just accepting a pointer to the stmmac_priv instance.

-Serge(y)

> +{
> +	if (!priv->hw->xpcs)
> +		return;
> +
> +	xpcs_destroy(priv->hw->xpcs);
> +	priv->hw->xpcs = NULL;
> +}
> +
>  /**
>   * stmmac_mdio_register
>   * @ndev: net device structure
> @@ -679,9 +688,6 @@ int stmmac_mdio_unregister(struct net_device *ndev)
>  	if (!priv->mii)
>  		return 0;
>  
> -	if (priv->hw->xpcs)
> -		xpcs_destroy(priv->hw->xpcs);
> -
>  	mdiobus_unregister(priv->mii);
>  	priv->mii->priv = NULL;
>  	mdiobus_free(priv->mii);
> 
> -- 
> 2.44.0
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH net-next v5 4/7] net: stmmac: introduce pcs_init/pcs_exit stmmac operations

[Serge Semin]

On Tue, Apr 30, 2024 at 09:29:44AM +0200, Romain Gantois wrote:
> From: "Russell King (Oracle)" <rmk+kernel@armlinux.org.uk>
> 
> Introduce a mechanism whereby platforms can create their PCS instances
> prior to the network device being published to userspace, but after
> some of the core stmmac initialisation has been completed. This means
> that the data structures that platforms need will be available.
> 
> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
> Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
> Co-developed-by: Romain Gantois <romain.gantois@bootlin.com>
> Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>

Reviewed-by: Serge Semin <fancer.lancer@gmail.com>

-Serge(y)

> ---
>  drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c | 8 +++++++-
>  include/linux/stmmac.h                            | 2 ++
>  2 files changed, 9 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
> index af8ad9768da10..1c788caea0cfb 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
> @@ -505,7 +505,10 @@ int stmmac_pcs_setup(struct net_device *ndev)
>  	priv = netdev_priv(ndev);
>  	mode = priv->plat->phy_interface;
>  
> -	if (priv->plat->mdio_bus_data && priv->plat->mdio_bus_data->has_xpcs) {
> +	if (priv->plat->pcs_init) {
> +		ret = priv->plat->pcs_init(priv);
> +	} else if (priv->plat->mdio_bus_data &&
> +		   priv->plat->mdio_bus_data->has_xpcs) {
>  		/* Try to probe the XPCS by scanning all addresses */
>  		for (addr = 0; addr < PHY_MAX_ADDR; addr++) {
>  			xpcs = xpcs_create_mdiodev(priv->mii, addr, mode);
> @@ -531,6 +534,9 @@ int stmmac_pcs_setup(struct net_device *ndev)
>  
>  void stmmac_pcs_clean(struct stmmac_priv *priv)
>  {
> +	if (priv->plat->pcs_exit)
> +		priv->plat->pcs_exit(priv);
> +
>  	if (!priv->hw->xpcs)
>  		return;
>  
> diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h
> index dfa1828cd756a..4a24a246c617d 100644
> --- a/include/linux/stmmac.h
> +++ b/include/linux/stmmac.h
> @@ -285,6 +285,8 @@ struct plat_stmmacenet_data {
>  	int (*crosststamp)(ktime_t *device, struct system_counterval_t *system,
>  			   void *ctx);
>  	void (*dump_debug_regs)(void *priv);
> +	int (*pcs_init)(struct stmmac_priv *priv);
> +	void (*pcs_exit)(struct stmmac_priv *priv);
>  	void *bsp_priv;
>  	struct clk *stmmac_clk;
>  	struct clk *pclk;
> 
> -- 
> 2.44.0
> 

Re: [PATCH net-next v5 4/7] net: stmmac: introduce pcs_init/pcs_exit stmmac operations

[Serge Semin]

On Tue, Apr 30, 2024 at 09:29:44AM +0200, Romain Gantois wrote:
> From: "Russell King (Oracle)" <rmk+kernel@armlinux.org.uk>
> 
> Introduce a mechanism whereby platforms can create their PCS instances
> prior to the network device being published to userspace, but after
> some of the core stmmac initialisation has been completed. This means
> that the data structures that platforms need will be available.
> 
> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
> Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
> Co-developed-by: Romain Gantois <romain.gantois@bootlin.com>
> Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>

Reviewed-by: Serge Semin <fancer.lancer@gmail.com>

-Serge(y)

> ---
>  drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c | 8 +++++++-
>  include/linux/stmmac.h                            | 2 ++
>  2 files changed, 9 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
> index af8ad9768da10..1c788caea0cfb 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
> @@ -505,7 +505,10 @@ int stmmac_pcs_setup(struct net_device *ndev)
>  	priv = netdev_priv(ndev);
>  	mode = priv->plat->phy_interface;
>  
> -	if (priv->plat->mdio_bus_data && priv->plat->mdio_bus_data->has_xpcs) {
> +	if (priv->plat->pcs_init) {
> +		ret = priv->plat->pcs_init(priv);
> +	} else if (priv->plat->mdio_bus_data &&
> +		   priv->plat->mdio_bus_data->has_xpcs) {
>  		/* Try to probe the XPCS by scanning all addresses */
>  		for (addr = 0; addr < PHY_MAX_ADDR; addr++) {
>  			xpcs = xpcs_create_mdiodev(priv->mii, addr, mode);
> @@ -531,6 +534,9 @@ int stmmac_pcs_setup(struct net_device *ndev)
>  
>  void stmmac_pcs_clean(struct stmmac_priv *priv)
>  {
> +	if (priv->plat->pcs_exit)
> +		priv->plat->pcs_exit(priv);
> +
>  	if (!priv->hw->xpcs)
>  		return;
>  
> diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h
> index dfa1828cd756a..4a24a246c617d 100644
> --- a/include/linux/stmmac.h
> +++ b/include/linux/stmmac.h
> @@ -285,6 +285,8 @@ struct plat_stmmacenet_data {
>  	int (*crosststamp)(ktime_t *device, struct system_counterval_t *system,
>  			   void *ctx);
>  	void (*dump_debug_regs)(void *priv);
> +	int (*pcs_init)(struct stmmac_priv *priv);
> +	void (*pcs_exit)(struct stmmac_priv *priv);
>  	void *bsp_priv;
>  	struct clk *stmmac_clk;
>  	struct clk *pclk;
> 
> -- 
> 2.44.0
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH net-next v5 2/7] net: stmmac: Add dedicated XPCS cleanup method

[Romain Gantois]

Hi Serge,

On Fri, 3 May 2024, Serge Semin wrote:

> 
> > +void stmmac_pcs_clean(struct stmmac_priv *priv)
> 
> Ideally it would have been great to have the entire driver fixed to
> accept the stmmac_priv pointer as the functions argument. But this
> would be too tiresome. Anyway seeing the PCS-setup protagonist method
> has the net_device pointer passed I would implement the same prototype
> for the antagonist even though it would require an additional local
> variable. That will make the MDIO and PCS local interface-functions
> looking alike and as if unified. That is the reason of why I made
> stmmac_xpcs_clean() accepting the net_device pointer. 
> 
> Alternatively both stmmac_pcs_setup() and stmmac_pcs_clean() could be
> converted to just accepting a pointer to the stmmac_priv instance.

I think that adapting stmmac_pcs_clean() to take a net_device struct would be 
more appropriate since it's the simpler of the two methods. I'll implement this 
in the next version.

Thanks,

-- 
Romain Gantois, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

Re: [PATCH net-next v5 2/7] net: stmmac: Add dedicated XPCS cleanup method

[Romain Gantois]

Hi Serge,

On Fri, 3 May 2024, Serge Semin wrote:

> 
> > +void stmmac_pcs_clean(struct stmmac_priv *priv)
> 
> Ideally it would have been great to have the entire driver fixed to
> accept the stmmac_priv pointer as the functions argument. But this
> would be too tiresome. Anyway seeing the PCS-setup protagonist method
> has the net_device pointer passed I would implement the same prototype
> for the antagonist even though it would require an additional local
> variable. That will make the MDIO and PCS local interface-functions
> looking alike and as if unified. That is the reason of why I made
> stmmac_xpcs_clean() accepting the net_device pointer. 
> 
> Alternatively both stmmac_pcs_setup() and stmmac_pcs_clean() could be
> converted to just accepting a pointer to the stmmac_priv instance.

I think that adapting stmmac_pcs_clean() to take a net_device struct would be 
more appropriate since it's the simpler of the two methods. I'll implement this 
in the next version.

Thanks,

-- 
Romain Gantois, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH net-next v5 2/7] net: stmmac: Add dedicated XPCS cleanup method

[Serge Semin]

On Mon, May 06, 2024 at 09:07:41AM +0200, Romain Gantois wrote:
> Hi Serge,
> 
> On Fri, 3 May 2024, Serge Semin wrote:
> 
> > 
> > > +void stmmac_pcs_clean(struct stmmac_priv *priv)
> > 
> > Ideally it would have been great to have the entire driver fixed to
> > accept the stmmac_priv pointer as the functions argument. But this
> > would be too tiresome. Anyway seeing the PCS-setup protagonist method
> > has the net_device pointer passed I would implement the same prototype
> > for the antagonist even though it would require an additional local
> > variable. That will make the MDIO and PCS local interface-functions
> > looking alike and as if unified. That is the reason of why I made
> > stmmac_xpcs_clean() accepting the net_device pointer. 
> > 
> > Alternatively both stmmac_pcs_setup() and stmmac_pcs_clean() could be
> > converted to just accepting a pointer to the stmmac_priv instance.
>
 
> I think that adapting stmmac_pcs_clean() to take a net_device struct would be 
> more appropriate since it's the simpler of the two methods. I'll implement this 
> in the next version.

Awesome! Thanks.

-Serge(y)

> 
> Thanks,
> 
> -- 
> Romain Gantois, Bootlin
> Embedded Linux and Kernel engineering
> https://bootlin.com

Re: [PATCH net-next v5 2/7] net: stmmac: Add dedicated XPCS cleanup method

[Serge Semin]

On Mon, May 06, 2024 at 09:07:41AM +0200, Romain Gantois wrote:
> Hi Serge,
> 
> On Fri, 3 May 2024, Serge Semin wrote:
> 
> > 
> > > +void stmmac_pcs_clean(struct stmmac_priv *priv)
> > 
> > Ideally it would have been great to have the entire driver fixed to
> > accept the stmmac_priv pointer as the functions argument. But this
> > would be too tiresome. Anyway seeing the PCS-setup protagonist method
> > has the net_device pointer passed I would implement the same prototype
> > for the antagonist even though it would require an additional local
> > variable. That will make the MDIO and PCS local interface-functions
> > looking alike and as if unified. That is the reason of why I made
> > stmmac_xpcs_clean() accepting the net_device pointer. 
> > 
> > Alternatively both stmmac_pcs_setup() and stmmac_pcs_clean() could be
> > converted to just accepting a pointer to the stmmac_priv instance.
>
 
> I think that adapting stmmac_pcs_clean() to take a net_device struct would be 
> more appropriate since it's the simpler of the two methods. I'll implement this 
> in the next version.

Awesome! Thanks.

-Serge(y)

> 
> Thanks,
> 
> -- 
> Romain Gantois, Bootlin
> Embedded Linux and Kernel engineering
> https://bootlin.com

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel